Concrete Repair
Tower Concrete Repair is an easy-to-apply textured sealant for horizontal surfaces. Use for mortar, stucco, grout, EIFS, concrete floors, sidewalks, driveways, patios, and decks. Paintable, low shrinkage, interior/exterior.
Colors:
CONCRETE REPAIR Textured Masonry Repair Sealant is designed to repair large or small cracks in concrete, brick or stone. This water-based acrylic product is for use on horizontal surfaces, such as sidewalks, garage floors, driveways, patios and more. CONCRETE REPAIR combines Tower’s best durability, flexibility and adhesion for lasting masonry crack repairs. Easy-to-apply, 100% modified acrylic latex water-based product is textured so repairs can be blended in. The cured bead is mildew and UV resistant, can be painted and exceeds the performance requirements of ASTM C-834 type OP, Grade -18°C.
- 1:Exceeds ASTM C-834 Type OP, Grade -18°C
- 2:Repair and waterproof cracks, gaps and defects in horizontal surfaces
- 3:Used for non-structural cracks or gaps from 1/8” to 1”
- 4:Outstanding Adhesion
- 5:Low Shrinkage
- 6:Mildew and UV Resistant
- 7:Vacuum Filled Tubes
- 8:Paintable
- Driveways
- Sidewalks
- Garage Floors
- Patios
- Stairs
- Masonry
- Ceramic Tile
- Stone
- Concrete
- Brick
- Cement
Surfaces to be caulked must be dry and free of all dirt, dust, oil, mildew, loose paint, old caulk or other contaminates. Only apply when sealant, surface, and air temperature are above 40ºF and rising. Do not apply on
surfaces that exceed 140ºF, or when rain is expected.
- Cut nozzle at a 45º angle. Cured bead should be between 1/8” and 1” wide. Use a foam backer rod for joints that exceed 1/2” in depth.
- Tool patch to match desired texture and profile of the surrounding area.
- Clean up uncured material and tools with soap and water.
- Allow 4 to 6 hours before painting.
Coverage: 55 linear feet for a 3/16” bead. Product will “skin-over” in 1 hour. Product may take 1-2 weeks to reach full cure, temperature and humidity dependent. Keep traffic off for at least 24 hours, longer if temperature is cool and humidity high.
NOT INTENDED FOR AREAS THAT WILL BE SUBMERGED IN WATER. KEEP FROM FREEZING. ALWAYS TEST FOR SUBSTRATE COMPATIBILITY.
Immediately after use, clean uncured material and tools with soap and water. Remove cured sealant by cutting with a sharp-edged tool.
- Vehicle: 100% Modified Acrylic Emulsion Polymer
- VOC: Non-chemically curing sealant. VOC (less exempt solvents) is <1.5%
- Pigment: Calcium Carbonate
- Solids: Approximately 85%
- Weight per Gallon: 14.25 ± 0.5
- Specific Gravity: Approximately 1.74
- Service Temp: -30ºF to 180ºF
- Temp Application Range: 40ºF and rising. Air temp no hotter than 95º and substrate not hotter than 140º
- Freeze Thaw Stability: Passes 5 Cycles@ 0ºF (1 cycle = 16hrs. @ 0ºF, 8hrs at 75ºF)
- Flash Point: None
- Consistency: Paste
- Applications: Interior / Exterior
- Shelf Life: 24 months when stored at 50ºF to 80ºF
- Coverage: 10.1 fl oz: 55 linear ft. at a 3/16” bead
- Odor: Mild Sweet Acrylic
- Tooling Time: 10 to 15 Minutes
- Tack Free Time: 60 Minutes
- Paint Over Time: 4 to 6 hours
- Full Cure: 5-10 days
- Packaging: 10.1 fl oz. (299 ml)
Product resources
